The Plastics Distributor and Fabricator - Your Industry Magazine
The Plastics Distributor and Fabricator, Your Industry Magazine
Plastic Spacer
News Features Series Articles Columns
Plastic Spacer
Return Home
Article Keyword Search
Acrylic Fabricating Supplies & Equipment
Acrylic Shapes
Painting Acrylic Sheet
Solvent Cementing
Laser Cutting Thermoplastics
Sawing Acrylics
Acrylic Sheet
 




FEATURES
Select issue:  


Acrylic Sheet

Acrylic sheet is commonly manufactured by one of three techniques. Each technique offers unique benefits from cost and physical properties to variety of color and finish. Depending on the fabricator’s needs, one type may be more appropriate than another. This article is meant to provide a layman’s explanation of the manufacturing methods and reiterate the differences between the end products. Volumes have been written on these processes and our intention is only to help differentiate them for you. Understanding the manufacturing processes and differences between the end products can assist you in choosing a material for your application.

Extruded Acrylic Sheet

Extrusion is a continuous production method of manufacturing acrylic sheet. In the extrusion process, pellets of resins are fed into an extruder which heats them until they are a molten mass. This mass is then forced through a die as a molten sheet. The molten sheet is fed to calender rolls, the spacing of which determine the thickness of the sheet and in some cases the surface finish. The continuous band of sheet may then be cut or trimmed into its final size.

The final product of extrusion exhibits much closer thickness tolerances than cast sheet. Because of the volume at which extruded sheet is produced, it is the most economical form you can buy. It is available in a fair selection of colors, finishes and sizes. Extruded acrylic sheet is prone to shrinking along the extruded line and expansion across it. This is of particular note if you plan to use it for thermoforming. Extruded material also has a tendency to gum during fabrication when the cutting is too fast (linear feed rate) because it has a lower molecular weight. It also may absorb fast drying solvent cements faster than cast or continuous cast material. This can result in joint failures and incomplete gluing. To remedy this, use slower drying cements and tooling designed for cutting extruded acrylic.

Continuous Cast Acrylic Sheet

Continuous Casting is also a mass production form for manufacturing acrylic sheet. The process involves pouring partially polymerized acrylic (somewhat less viscous than “Karo” syrup) between line. two highly polished stainless steel belts. The belts are separated by a space equal to the thickness of the sheet and the “syrup is retained by gaskets at the edge of the belts. The belts move through a series of cooling and heating units to regulate the curing and are cut “on the fly” to size at the end of the production line.

One advantage of this process partial polymerization of the material prior to casting. Some of the heat of polymerization, heat which is evolved as the liquid monomer is converted to a solid resin, is removed before the “syrup” is fed to the belt system. This contributes to the control of the continuous process.

The material cost for continuous cast versus extruded sheet favors continuous casting as the cost of monomer is much lessthan that of polymer pellets. Further, the production cost per unit of product, lbs./hr./$ capital investment, will be less for extrusion. Which process is more economical depends on the capacity and utility of the facilities as well as the cost of materials and equipment. In terms of competitive pricing between continuous cast and extruded acrylic, there are approximately a dozen extruders of acrylic sheet and only two continuous cast manufacturers in the U.S. This will have obvious effects on competitive pricing.

Cell Cast Acrylic Sheet

Cell Casting historically has been carried out using any of three processes. The first is the water bath technique. Acrylic syrup is poured into a mold typically constructed from two tempered glass sheets separated to produce the desired thickness of the sheet and sealed with a gasket at the edge. The mold is submerged in a bath which maintains/ controls a curing temperature and efficiently removes the heat generated in the process when the monomer is converted to polymer. Note - Monomer is not used in cell casting. The viscosity of acrylic monomer must be raised somewhat to avoid leakage of the molds or cells.

The two other casting techniques currently used include the original process which involved placing the “molds” containing a “syrup” in a circulating air oven in which air at a controlled temperature passes at a moderately high velocity over the surface of the mold .

The third method, an advancement over the water bath process, was developed by the Polycast Company. It involves the use of a piece of equipment similar to a plate and frame filter press. Sections which serve as the mold for the sheet are alternately configured with sections through which water at a regulated temperature is circulated to promote the polymerization and cure of the sheet.

Cell Cast products should be subjected to a “post-cure” or “annealing” process. The sheet, as taken from the oven, bath or casting machine, will usually have a “high” residual monomer content. The polymerization process is not complete. Post-curing reduces the residual monomer content and serves to insure that no bubbling of the sheet occurs if the sheet is heated for thermoforming.

In casting sheet from syrup a change in density (specific gravity) of the ingredients occurs. A shrinkage of about 20% is experienced. In the cell casting process most shrinkage occurs in the thickness direction. The surface of the mold (tempered glass sheet) restrains the plastic sheet from shrinkage in the length-width direction. Hence, the annealing, in which the sheet is heated to its softening point, allows it to relax or shrink removing residual stress.

Which sheet is right for your fabrication job? Cell Cast products provide optical clarity, greater surface hardness and machine cleanly. They are offered in many colors, finishes and thicknesses They do, however, have greater thickness variation making them less desirable for fitting into extrusions or thermoforming where uniform wall thickness must be maintained.

Continuous Cast acrylic offers good optical clarity, more uniform thickness and limited shrinkage during thermoforming. However, it is not as hard as Cell Cast material which means it is prone to show scratches and does not machine as cleanly without adjustments to feed rates and tool geometry. Being mass produced, it also does not offer as many color and thickness options.

Extruded sheet is by far the most uniform and usually the most economical. It is offered in a growing number of colors, finishes and thicknesses which should satisfy most acrylic applications.


Re-edited from an article appearing in the November/December 2000 issue of Plastics Distributor® & Fabricator written by George Graf, Graf Enterprises, Inc. Mr. Graf has over 50 years working in the acrylic resin manufacturing and processing industry. His background includes 39 years with DuPont and 15 years as a consultant to the industry. Recognized as an authority in the economics of plastic processing and converting; he holds patents for fabric reinforced resin constructions and acrylic polymer manufacture.

Return Home | Back To Top
Plastic Spacer

 
Copyright © 2024
Plastics Distributor® & Fabricator Magazine
P.O. Box 669
LaGrange, Illinois 60525-0669
All Rights Reserved.
Header Image courtesy of Nylatech, Inc.

Phone: (708) 588-1845
Fax: (708) 588-1846
Email Us