The Plastics Distributor and Fabricator - Your Industry Magazine
The Plastics Distributor and Fabricator, Your Industry Magazine
Plastic Spacer
News Features Series Articles Columns
Plastic Spacer
Return Home
Article Keyword Search
 
ARTICLES
Category: Tooling
Volume: 28
Issue: 2
Article No.: 4565

BROWSE ARTICLES
BY CATEGORY: < Previous | Next >
BY ISSUE: < Previous | Next >
Back To Article Directory - Mar/Apr-07


ROUTING: Real World Routing Solutions

Part 1 of this four-part series offers practical tooling
solutions for three common routing problems.


Sometime in the early 1980s, dedicated router tooling for plastics began to take shape. Since then, there have been leaps in technology from all areas in the primary plastics market including material composition, fabrication, machines and machining. Each area has gone through growth spurts that have surpassed the capabilities of the other areas, which in turn has led the other industry sectors to improve their R&D work and leap ahead again. While this rapid growth has created a large and viable plastics market, it has also led to confusion about methods and practices when it comes to producing these indemand plastic products. With an ever increasing burden on the plastic fabricator to produce parts faster and with better finishes, companies are looking for more and more technical assistance from suppliers in solving these problems.

A number of application problems have been observed that are significant to a large segment of primary and secondary fabricators. In line with this experience, I will present 12 scenarios over the course of the next four articles that illustrate real-life applications and the actual tooling solutions that were implemented to solve either a manufacturing problem or a production problem.


Scenario 1
Material Cut:
ABS
Product: Thermoformed tractor shrouds and fuel tanks
Router Type: Hand held air router
Feeds & Speeds: Manual operation at 21,000 rpm
Initial Tooling: HSS Pilot bits and standard Carbide Tipped V flute bits
Problems: Tool breakage, production bottleneck and poor part finish

This company had “lived with” the routing department as it was for quite some time and only recently completed a study that pointed to that area as a root cause for some less than desirable production bottlenecks. After visiting the plant, it was apparent that the routing group needed both a tooling and an application change. The HSS pilot bits were being used with a guide template to cut holes in the fuel tanks, but were breaking when used for fast, hand-held free-routing operations. The continuing bit breakage was causing short, but frequent downtime when the collets and nose guards were disassembled to replace the tooling. The carbide-tipped bits were resistant to the breakage associated with the pilot bits, but were producing a poor finish with evident chatter (Figure A).

HSS double-edged “O” flutes, designed specifically for air-routers, were tested on-site and were able to immediately replace the carbide tipped double edge V flutes. These “O” flutes are dedicated plastic tools designed for cutting soft plastics and their open flute shape allowed the ABS to naturally curl when cut, eliminating the chatter of the straight faced carbidetipped tooling. Their feed was also more controlled, while still being easier to push - eliminating some production personnel complaints.

When the HSS double edge “O” flutes were tested against the pilot bits, their feed speed and pressure were an improvement. But they still lacked a method of guiding on the templates, used for production of the fuel cells.

In order to solve this problem in previous applications, the air-router “O” flute design had been changed to give an extended overall length. This allowed the tool to seat normally in the collet, protrude through the nose bearing of the router (giving important extra stability) and through an additional guide bushing. By utilizing this guide bushing, the routing department made new templates for the fuel cells and virtually eliminated breakage.


Scenario 2
Material Cut:
Extruded (soft) acrylic
Product: Various Point-of-Purchase displays
Router Type: 3-axis CNC in excellent condition
Feeds & Speeds: 100 ipm at 18,000 rpm
Initial Tooling: Generic solid carbide “O” flute
Problems: Intermittent melting required finishing and/or clean up operations. Paper masking would wrap/adhere to the cutter

The first problem in this plant was the tooling choice. Earlier articles have stated the need for dedicated plastic tooling to achieve maximum feed rates and optimal finishes. Tooling that works well in ABS probably won’t perform as well in polycarbonate. Tooling that leaves a clear edge in cast acrylic may melt and scar extruded acrylic. With this in mind, the single edge solid carbide straight “O” flute was replaced with a similar spiral “O” flute. This replacement had geometry designed specifically for melt-prone plastics. This instant solution cleared up the melt problem and saved on both inspection and rework time for the fabricator (Figure B).

The solution for the second problem, the wrap-up of the paper masking, followed as a direct result of the correct tool choices. The plastic geometry spiral “O” flute was designed to handle a high chip load and thereby reduce heat build up during cutting. By doubling the feed rate to 200 ipm and reducing the spindle speed to 14,000 rpm, the cutter stayed cool enough to prevent the tacky glue from warming and adhering to the cutter body, while still maintaining a good part finish. By changing cutters to a dedicated plastic tool, the fabricator walked away from this problem with a number of benefits: production speed nearly doubled, inspection time was reduced and rework time due to machining inconsistencies nearly eliminated. The tooling was nearly identical to dimensions to the original and therefore required no reprogramming or refixturing (Figure C).


Scenario 3
Material Cut:
1/2-inch to 1-inch thick corrugated paper core with plastic laminate (both sides)
Product: Custom packaging
Router Type: 5-axis CNC
Feeds & Speeds: Variety tested, initial production run
Initial Tooling: Variety tested, initial production run
Problems: Unable to cleanly cut the material; Lifting of material from vacuum fixturing

More and more router owners in the plastic industry have questions about corrugated or honeycomb panels that have plastic, composite or aluminum laminated skins. The high strength-to-weight ratio of these structures has led to their use in aerospace and marine applications. Their high cost and technical machining requirements, however, had previously kept them from widespread market acceptance. With falling prices and advanced tooling rising to the challenge, markets that had previously ignored composite sandwich panels are starting to use them in everyday applications such as custom packaging.

This particular fabricator had tried both high speed steel and solid carbide straight and spiral tooling in this application. The HSS tooling wore down quickly due to the abrasive paper core and the solid carbide straight tooling could not produce an optimal edge on both the top and bottom surface. The solid carbide downcut spirals worked the best - solving the fabricators hold-down problems, but still leaving a frayed bottom panel.

The final tooling solution was a special compression router bit that was designed for the wood composites market and has been a staple in the honeycomb and laminated composites industry for many years. The mortise compression spiral is a hybrid cutter that uses a 0.200-inch long upcut spiral near the tip of the tool and an extended downcut spiral that overlaps the upcut by about 0.060 inch and continues up the cutting edge. While it is a non-traditional plastic tool, the combined cutting action of the opposing spirals, in conjunction with the location of the overlap, allowed this tool to shear the laminated materials toward the center of the corrugated materials and produce an excellent edge finish on both the top and bottom of the part. The short upcut allowed the router to run without tool changes because the same tool could cut materials ranging from 1/4 inch to 11/2 inch (Figure D).

The best edge finish of both the paper core and the plastic laminate was obtained at 450 ipm and 18,000 rpm, but at these feed rates the material normally lifted from the fixture with other types of tooling. Because of the long downcut length of the mortise compression spiral, extra downward holding pressure was generated from the router bit itself and the material stayed securely fixtured.

The right tool for the job is a critical component of each fabrication or trimming process. As materials change and multiply, tooling must keep pace. New router bits for plastic are designed every month and their proper use can help ensure optimum productivity. Look for more specific applications in the months ahead.


For more information, click on the author biography at the top of the page.

Return Home | Back To Top
Plastic Spacer

 
Copyright © 2024
Plastics Distributor® & Fabricator Magazine
P.O. Box 669
LaGrange, Illinois 60525-0669
All Rights Reserved.
Header Image courtesy of Nylatech, Inc.

Phone: (708) 588-1845
Fax: (708) 588-1846
Email Us